SINOCONVE MXL T-Type Rubber Timing Belt
The SINOCONVE MXL rubber timing belt is built around fine-pitch precision. With a confirmed 2.032 mm pitch, 0.51 mm tooth height and 1.14 mm belt thickness, it is intended for trapezoidal tooth engagement in precision instruments, indexing mechanisms and compact synchronous equipment.
The supplied construction uses high-quality synthetic CR rubber, fiberglass cord and highly wear-resistant nylon elastic fabric on the tooth surface. This combination is described for accurate synchronous transmission without normal operating slip, repeated dynamic bending and resistance to cracking, ozone, aging, heat and wear.
Get the correct MXL specification faster
Use Inquiry Now and send the complete belt marking, T-Type profile, belt width, teeth number or pitch length, pulley data, speed, power or torque, quantity and operating conditions.
Confirmed MXL technical data
| Tooth Profile Family | T-Type |
| Type | MXL |
| Pitch | 2.032 mm |
| Tooth Angle | 40° |
| Bottom Tooth Thickness | 1.14 mm |
| Tooth Height | 0.51 mm |
| Belt Thickness | 1.14 mm |
| Teeth Number Range | 43-2044 |
| Pitch Length Range | — |
| Belt Body | Synthetic CR Rubber |
| Reinforcement | Fiberglass Cord |
| Tooth Fabric | Wear-Resistant Nylon Elastic Fabric |
Profile compatibility note
MXL is not selected by pitch alone. Confirm the T-Type tooth geometry, pulley tooth form, belt width, tooth count or pitch length, pulley tooth counts, center distance and installation tension before production.
Why buyers consider this MXL timing belt
Positive synchronous engagement
Repeatable synchronous positioning and positive engagement with a matching trapezoidal pulley when profile, pulley geometry and installation tension are correctly matched.
Controlled elongation
Fiberglass cord reinforcement is used to help control belt stretch during repeated synchronous operation.
Protected tooth surface
Wear-resistant nylon elastic fabric protects the tooth contact area during repeated meshing.
Timing-belt construction and engagement
Positive synchronous engagement
The molded tooth profile is intended to engage a matching timing pulley. Correct tooth profile, pulley geometry and installation tension are required for stable synchronous motion.
Profile-specific selection
For the MXL type, confirm pitch, belt width, teeth number or pitch length, pulley tooth profile, pulley tooth counts, speed and load before production.
Rubber body and reinforcement
The listed construction uses Synthetic CR Rubber, reinforced with Fiberglass Cord. The tooth contact surface is protected by Wear-Resistant Nylon Elastic Fabric. Final construction should be confirmed against the required operating conditions.
Operating properties from the supplied specification
- Excellent dynamic curve performance
- Crack resistance
- Ozone resistance
- Anti-aging performance
- Heat resistance
- Wear resistance
Selection information to confirm
- Complete belt marking and MXL / T-Type profile identification.
- Pitch length or teeth number, belt width and required quantity.
- Matching pulley tooth profile, pulley tooth counts and center distance.
- Speed, power or torque, installation tension and duty cycle.
- Operating temperature, dust, oil, moisture and other environmental conditions.
- Sample, drawing, custom marking, packaging or inspection-document requirements.
A timing belt must use a pulley with matching pitch and tooth geometry. Final dimensions and commercial terms are subject to order confirmation.
T-Type profile reference
The table below keeps the supplied technical reference within the same profile family. A dash means the source workbook did not confirm that value.
| Type | Pitch | Tooth Height | Belt Thickness | Teeth Range |
|---|---|---|---|---|
| MXL | 2.032 mm | 0.51 mm | 1.14 mm | 43-2044 |
| XXL | 3.175 mm | 0.76 mm | 1.52 mm | 46-124 |
| XL | 5.080 mm | 1.27 mm | 2.30 mm | 22-510 |
| L | 9.525 mm | 1.91 mm | 3.60 mm | 23-530 |
| H | 12.700 mm | 2.29 mm | 4.30 mm | 29-440 |
| XH | 22.225 mm | 6.35 mm | 11.20 mm | 53-220 |
| XXH | 31.750 mm | 9.53 mm | 15.70 mm | 56-144 |
| T2.5 | 2.5 mm | 0.70 mm | 1.30 mm | 42-312 |
| T5 | 5 mm | 1.20 mm | 2.20 mm | 30-400 |
| T10 | 10 mm | 2.50 mm | 4.50 mm | 34-536 |
| T20 | 20 mm | 5.00 mm | 8.00 mm | 61-181 |
Typical application scope
The supplied T-Type product description covers precision machinery, packaging equipment, printing systems, indexing drives, office equipment and general synchronous transmission. This MXL page emphasizes precision instruments, indexing mechanisms and compact synchronous equipment while final suitability remains subject to pulley matching and application confirmation.
Request a technical recommendation and quotation
Click Inquiry Now and provide the belt marking or MXL profile, required width, teeth number or pitch length, pulley geometry, speed, torque or power, quantity and environment.
Suggested inquiry: “Please quote MXL T-Type rubber timing belts, width [ ], teeth number / pitch length [ ], quantity [ ], pulley profile [ ], speed [ ], power or torque [ ], and operating conditions [ ].”
Frequently asked questions
What is the pitch of the MXL timing belt?
The supplied specification confirms a pitch of 2.032 mm.
What tooth profile family does MXL use?
It belongs to the T-Type family and is intended for trapezoidal tooth engagement.
What construction is specified?
The source data lists Synthetic CR Rubber, Fiberglass Cord and Wear-Resistant Nylon Elastic Fabric.
Can width and length be customized?
The source attributes state Available. Final dimensions require order confirmation.
What should I send for a quotation?
Send the complete marking, profile, pitch length or tooth count, width, pulley data, speed, power or torque, quantity and environment.
Rubber Timing Belt Profile Reference
Company information
