SINOCONVE A32 Transmission Rubber Drive Wrapped V-Belt for Industrial Pulley Drives
The SINOCONVE A32 wrapped V-belt is intended for classical pulley drives in industrial equipment. It combines an A-section belt profile with a fabric-covered rubber body and polyester cord reinforcement, providing a practical replacement format for machinery that transfers power through matched sheaves.
Before selecting an A32 belt, compare the marking on the removed belt with the pulley groove, measured length, center distance and tensioning travel. Motor power, running speed, start-stop frequency and exposure to oil, heat or dust should also be supplied for an application-based recommendation.
Make the replacement specification clear
Click Inquiry Now and provide the A32 marking, measured length, pulley groove dimensions, center distance, motor speed, load, quantity and working conditions.
A32 product overview
| Product | A32 transmission rubber drive wrapped V-belt |
| Profile designation | A32 |
| Transmission method | Classical V-belt friction drive with matching pulley grooves |
| Rubber material reference | NR/SBR rubber layers listed in the legacy material |
| Cord and cover | Polyester cord with polyester-cotton outer canvas |
| Related equipment | Blending systems, choppers, HVAC equipment, lawnmowers, compressors, crushers and scarifiers |
Performance information to confirm
The supplied legacy material refers to high loads, low elongation, fatigue endurance, operational safety, oil/heat/ozone/abrasion resistance, static conductivity to ISO 1813 and -55°C to 70°C. Confirm the selected compound, supporting documents and actual service range before using these as fixed guarantees.
Construction and operating role
A-section contact with the sheave
The V profile is intended to sit in a compatible pulley groove. Correct groove geometry and alignment are essential to the replacement review.
Cord-supported belt body
Polyester cord is listed as the reinforcing member. Load, speed and tension conditions should be checked before final selection.
Layered material reference
The legacy structure identifies NR/SBR top rubber, polyester cord, NR/SBR buffer rubber, NR/SBR bottom rubber and polyester-cotton outside fabric.
Cover and environment
The outer fabric and rubber compound should be considered alongside oil, heat, ozone, abrasion and dust exposure at the machine.
Equipment applications
Machinery reference list
Existing product material references blending systems, choppers, HVAC systems, lawnmowers, compressors, crushers and scarifiers. These references should be matched with the actual pulley arrangement and duty cycle.
A32 replacement checklist
- Photograph or record the full marking on the removed belt.
- Measure the belt length and record the pulley groove dimensions.
- Note center distance, shaft layout, alignment and available tension travel.
- Provide motor power, running speed, load and start-stop frequency.
- Describe oil, heat, ozone, dust, chemicals and other site conditions.
- Confirm quantity, packaging and any required technical documents.
A-section dimensional reference
| Section | Top width (mm) | Pitch width (mm) | Height (mm) | Reference length (mm) | Angle |
| A | 13 | 11 | 8 | 330–8000 | 40° |
This A-section table comes from the supplied legacy reference. A32 is the product designation shown by the seller; confirm the finished length separately from the complete marking and machine measurements.
Discuss the right configuration
For a quotation, provide the A32 marking together with the existing belt length, pulley data and operating load. The belt team can then review whether the requested designation matches the current drive arrangement.
Request an A32 belt review
Click Inquiry Now and send your machine type, A32 marking, measured length, pulley dimensions, speed, load and quantity.
Suggested inquiry: “Please review an A32 transmission rubber drive wrapped V-belt for [machine], length [ ], pulley details [ ], center distance [ ], speed [ ], load [ ] and quantity [ ].”
Frequently asked questions
What type of drive uses the A32 belt?
The A32 is positioned for classical pulley-and-shaft power transmission in industrial machinery. The matching groove and finished dimensions must be confirmed.
What should be measured before replacement?
Record the full belt marking, measured length, pulley groove, sheave diameter, center distance, alignment and tension adjustment range.
What materials are shown in the construction reference?
The legacy material lists NR/SBR rubber layers, polyester cord reinforcement and polyester-cotton outer fabric. Confirm the final construction for the operating conditions.
How do I request a quotation?
Use the Inquiry Now link and include the A32 marking, length, pulley data and quantity.
A-Type Wrapped V-Belt Reference
Production process
Company information
